Горный информационно-аналитический бюллетень. Mining informational and analytical bulletin. №2/2014

ТИТУЛЬНЫЕ СТРАНИЦЫ 
СОДЕРЖАНИЕ



ПОДЗЕМНАЯ РАЗРАБОТКА МЕСТОРОЖДЕНИЙ
Underground mining


ЕРШОВ А.А.

ВЛИЯНИЕ ПОРЯДКА ОТРАБОТКИ СБЛИЖЕННЫХ РУДНЫХ ТЕЛ НА УСТОЙЧИВОСТЬ КАМЕР
Выявлены закономерности формирования напряженного состояния руд и вмещающих пород в зоне ведения очистных работ на Агинском месторождении на основе математического моделирования. В расчетах использовалась модель однородной изотропной линейно-упругой среды.
Рассмотрен вариант разделения рудной залежи на участки целиками, либо применение систем с обрушением и переход на полевую подготовку, или закладку выработанного пространства для предотвращения неуправляемого обрушения вмещающих пород, приводящего к сверхпроектному разубоживанию руды и неожиданному разрушению выработок.
Приведены результаты моделирования распределения напряжений в горизонтальном сечении, когда залежь в висячем боку полностью отработана, а в лежачем боку работы только начинаются, представлены на рис. 4 и 5. Моделирование проводилось с целью изучения взаимного влияния сближенных рудных тел при их одновременной отработке.
Ключевые слова: сближенные рудные тела, рудная залежь, напряженное состояния руд, целики, охраняемые выработки.

ERSHOV A.A.
INFLUENCE OF MINING SEQUENCE ON STABILITY OF STOPES IN CONTIGUOUS ORE BODIES

The author has revealed the mechanism of stress state of ore and host rock mass in the vicinity of stoping operations in Aginskoe Mine using the mathematical model of an isotropic, linearly elastic medium. The article surveys scenarios of ore body splitting into blocks using pillars, or application of mining systems with caving and in-stone development, or mining with backfilling, aimed at prevention of sudden caving of host rocks and subsequent extra dilution of ore and failure of mine roadways.
The plan views of the modeled stress distribution for the mining situation when hanging wall is totally extracted and footwall operation is recently started are shown in Figs. 4 and 5. The objective of the modeling was the mutual influence of the contiguous ore bodies under concurrent mining.
Key words: contiguous ore bodies, ore deposit, stress state of ore, pillars, supported mine roadways.


КОМАЩЕНКО В.И., ЕРОХИН И.В.
КОНЦЕПЦИЯ МИНИМИЗАЦИИ ОПАСНОГО ЗАГРЯЗНЕНИЯ ОКРУЖАЮЩЕЙ СРЕДЫ ЖЕЛЕЗОРУДНЫХ РЕГИОНОВ КМА

Рассмотрена концепция минимизации опасного загрязнения воздушной среды, а также разработаны мероприятия по защите окружающей среды. При этом установлено, что эффективная реализация природоохранных мер возможна на базе соответствующего развития экономики, науки, техники и всестороннего совершенствования знаний о гармоническом взаимодействии горняков с окружающей средой. Обоснованно, что для определения интегрального уровня загрязнения целесообразно применять численное моделирование распространения пыли в атмосфере. Входными параметрами для моделирования являются их объемы выбросов, характеристика (диаметр и плотность пылегазовых частиц) и природные условия (направление и скорость ветра, температура внешней среды, метеорологические условия).
Ключевые слова: разработка месторождений, полезные ископаемые, загрязнение среды, карьеры, вскрышные породы, загрязнение воздуха, экосистемы, атмосфера, вентиляция, запыленность, концепция, горное предприятие, выброс вредных ингредиентов, метеорологические условия, окружающая среда.

KOMASHCHENKO V.I., YEROKHIN I.V.
THE CONCEPT OF MINIMIZING HAZARDOUS AIR POLLUTION AND MINING ENGINEERING PROTECTION AGAINST THE HARMFUL EFFECTS

Dealt with the concept of minimization of hazardous air pollution, as well as activities designed to protect the environment. It found that effective implementation of conservation measures is possible on the basis of the development of economy, science, technology and overall improvement of knowledge about harmonic interaction of the miners with the environment.
Rightly, that to determine the cumulative pollution it is expedient to apply numerical simulation of distribution of dust in the atmosphere. Input parameters for the modelling of emission characteristics (diameter and density of the gas particles) and environmental conditions (wind direction and speed, ambient temperature, weather conditions).
It is established that the numerical simulation of distribution of dust in the atmosphere, emissions are input parameters, characteristics of particles and natural conditions.
Key words: Mining, minerals, environment, career, overburden, air pollution, ecosystems, climate, ventilation, dust, concept mining enterprise, the emission of harmful ingredients, meteorological conditions, environment.


КУРИЛКО А.С., ДРОЗДОВ А.В., АЛЕКСЕЕВ К.Н., НИКИФОРОВА А.Д.
ВЛИЯНИЕ ХЛОРИДНЫХ КАЛЬЦИЕВЫХ РАССОЛОВ НА ПРОЧНОСТЬ ТОРКРЕТ-БЕТОНА, ИЗГОТОВЛЕННОГО НА ОСНОВЕ МЕСТНЫХ ЗАПОЛНИТЕЛЕЙ (НА ПРИМЕРЕ РУДНИКА «УДАЧНЫЙ»)

Приведен химический состав природного рассола отобранного с горизонта -380 абс. м рудника «Удачный», произведена оценка его агрессивности по отношению к бетону согласно СНиП 2.03.11-85. Исследовано влияние среды твердения (нормальные условия, рассол) и водоцементного отношения на предел прочности при сжатии различных составов торкрет-бетона изготовленного на местном заполнителе (отсев долеритового щебня производства АК «АЛРОСА»). Приведено изменение содержания химических элементов рассола после хранения в нём исследуемых образцов торкрет-бетона в течение 28 суток. Предложены пути повышения коррозионной стойкости бетона. Полученные в ходе лабораторных исследований данные необходимо учитывать при производстве торкрет-бетонных работ на руднике «Удачный».
Ключевые слова: торкрет бетон, заполнитель, отсев долеритового щебня, рассол, коррозия, прочность.

KURILKO A.S., DROZDOV A.V., ALEKSEEV K.N., NIKIFOROVA A.D.
INFLUENCE OF CALCIUM CHLORIDE UNDERGROUND BRINES ON THE STRENGHT OF SPRAYED CONCRETE, WHICH IS MADE ON THE BASIS OF LOCAL FILLERS (BY THE EXAMPLE OF MINE «UDACHNIY»)

Underground waters of mine «Udachniy» present the strong brines of calcium chloride salts with mineralization of salts more than 400 g/l. The article shows the chemical composition of natural brine selected from the horizon -380 abs. m. Evaluation of brine aggressiveness to concrete made in accordance with Building norms and rules 2.03.11-85 «Protection of building structures from corrosion». The article also describes the possible types corrosion of concrete when exposed to adverse hydrochemical conditions being built mine «Udachniy». Currently, construction of shotcrete concrete powered supports accomplished in mine workings of horizon -380 abs. m and in the pit bottom of horizon -580 abs. m. In this regard, we investigated the influence of hardening medium (normal conditions, brine) and the water-cement ratio on the compressive strength of different compositions shotcrete concrete made based on the local filler (dropouts dolerite crushed stone production «ALROSA»). Investigation shows the change contents of chemical elements of the brine after storage of the samples it shotcrete concrete within 28 days. Suggests ways to increase the corrosion resistance of concrete. Obtained in laboratory data need to be considered in the production of shotcrete concrete of works at the mine «Udachniy».
Key words: shotcrete concrete, filler, dropout dolerite crushed stone, brine, corrosion, strength.


СМИРНОВ С.М., ЕРЁМЕНКО А.А.
ВЫБОР И ОБОСНОВАНИЕ СОСТАВА ЗАКЛАДОЧНОЙ СМЕСИ ИЗ МЕСТНЫХ МАТЕРИАЛОВ ПРИ СЛОЕВОЙ СИСТЕМЕ РАЗРАБОТКИ РУБЦОВСКОГО ПОЛИМЕТАЛЛИЧЕСКОГО МЕСТОРОЖДЕНИЯ ОАО «СИБИРЬ-ПОЛИМЕТАЛЛЫ»

Предложена схема отработки технологического блока с закладкой твердеющими смесями. Определены горизонтальные и вертикальные напряжения.
Установлены средние значения прочности закладки для верхнего и нижнего уровней слоя. Предложена методика расчета нормативной прочности закладки по каждому слою этажа отработки рудного тела. Обоснован состав закладочной смеси из местных материалов при слоевой системе разработки Рубцовского полиметаллического месторождения.
Ключевые слова: месторождение, закладка, блок, разработка, устойчивость, прочность.

SMIRNOV S.M., EREMENKO A.A.
SELECTION AND SUBSTANTIATION OF A FILL COMPOSITION MADE OF LOCAL RAW MATERIALS AT RUBTSOVSK POLYMETAL ORE DEPOSIT DEVELOPED BY THE SLICE MINING PROCESS, OAO SIBIR-POLIMETALLY URAL MINING-METALLURGICAL COMPANY

The block mining and consolidating stowing process is proposed. The horizontal and vertical stresses are evaluated. The average stowing strength values for the upper and lower layers are found. The procedure for the calculation of the characteristic strength for every mining level is developed. The stowing mixture composition made of local raw materials is substantiated for the slice mining conditions at Rubtsovsk polymetal ore deposit.



ОТКРЫТЫЕ ГОРНЫЕ РАБОТЫ
Open-cast


ЖАРИКОВ В.П.
ГЕОЛОГО-ЭКОЛОГИЧЕСКОЕ ОБОСНОВАНИЕ РЕКУЛЬТИВАЦИИ ГИДРООТВАЛОВ ОТКРЫТОЙ РАЗРАБОТКИ УГЛЯ В КУЗБАССЕ

Рассмотрены инженерно-геологические условия гидроотвалов вскрышных пород Кузбасса, приведены агрохимические свойства техногенных насыпных и намывных пород, предложено для рекультивации гидроотвалов использовать размещение на поверхности намывного массива насыпи в виде «сухого» отвала определенной высоты, изучено влияние гидроотвала на работу водозабора питьевой воды г. Белово.
Ключевые слова: инженерно-геологические условия, агрохимические свойства, гидроотвал, намывные и насыпные техногенные породы, отвалообразование, водозабор питьевой воды, питание водоносного горизонта.

ZHARIKOV V.P.
EOLOGICAL-AND-ECOLOGICAL BASIS FOR RECLAMATION OF SLURRY DUMP AREAS AT OPEN PIT COAL MINES IN KUZBASS

The article describes geotechnical conditions in slurry dumps, reviews agrochemical properties of waste accumulated in dry-dumps and hydraulic fills, suggests reclamation of slurry dumping areas by dry rock dumping for a certain height on the surface of hydraulic frill dump and studies effect of a slurry dump on the drink water intake in the town of Belovo.
Key words: geotechnical conditions, agrochemical properties, slurry dump, hydraulic fill and dry-dump waste rocks, dumping, drink water intake, aquifer recharge.


ЖИГУЛЬСКАЯ А.И., БЕЛЯКОВ В.А.
ТЕХНОЛОГИЯ ИСПОЛЬЗОВАНИЯ ДРЕВЕСИНЫ, ПОЛУЧЕННОЙ ПРИ ГЛУБОКОМ СПЛОШНОМ ФРЕЗЕРОВАНИИ ТОРФЯНОЙ ЗАЛЕЖИ

Древесные включения в торфяной залежи оказывают значительное влияние на технологические процессы добычи торфа. Кроме того, их наличие приводит к значительному увеличению динамических нагрузок в элементах привода и конструкции торфяных машин. Расчет объемов древесных включений в слое торфяной залежи после глубокого фрезерования позволяет разработать варианты схем получения торфяной продукции на основе исходного сырья, получаемого данным способом.
Ключевые слова: торфяная залежь, древесные включения торфа, кустарники и мелколесье, глубокое фрезерование, подготовленный слой, побочные продукты торфодобычи, варианты малогабаритных технологических схем переработки.

ZHIGULSKAYA A.I., BELYAKOV V.A.
THE TECHNOLOGY OF USING WOOD OBTAINED BY MILLING A SOLID DEEP PEAT DEPOSITS

Wood inclusion in the peat deposits have a significant impact on technological processes of extraction of peat. In addition, their presence leads to a significant increase in dynamic loads in the elements of the drive and the construction of peat machines. The calculation of the volume of wood inclusions in the layer of peat deposits after deep milling allows the development of options schemes for peat products based on the source of raw materials delivered in this way.
The obtained calculation data on the volumes of secondary wood for the particular peat bog allow assessing future prospects of the given raw material to be introduced in advanced technologies of peat and its woody inclusions processing.
Key words: peat deposit, incorporating wood peat, shrubs and undergrowth, deep milling, prepared by layer, by-products peat extraction, small-sized versions of technological schemes of processing of.


МАМАЕВ Ю.А., ХРУНИНА Н.П.
ОСНОВНЫЕ ГЕОТЕХНОЛОГИЧЕСКИЕ ОСОБЕННОСТИ ВЫСОКОГЛИНИСТЫХ ЗОЛОТОСОДЕРЖАЩИХ ПЕСКОВ РОССЫПЕЙ ПРИАМУРЬЯ

На основе многофакторного анализа выделены объекты золотороссыпных месторождений Приамурья, включение в эксплуатацию которых сдерживается недостаточным уровнем техники и технологии добычи из-за высокого содержания мелкого и весьма мелкого золота и повышенной глинистости золотосодержащего пласта песков.
Ключевые слова: мелкое золото, глинистость, плотность песков, волновое сопротивление.

MAMAEV U.A., КHRUNINA N.P.
BASIC OF GEOTECHNOLOGICAL CHARACTERISTICS HIGH CLAY GOLD CONTAIN OF SANDS PLACERS OF PRIAMURIY

On a theoretical footing of much factor analysis excreted objects of gold placers Priamuriy, inclusion in exploitation which restrained insufficient level of technician and technology mining from behind high content of small and much small of gold and high clay gold contain a layer of sands.
Key words: small gold, clay, density of sands, acoustic waves resistance.



ОБОГАЩЕНИЕ ПОЛЕЗНЫХ ИСКОПАЕМЫХ
Enrichment of minerals


ЗАХАРОВ Ю.Н., ЩЕРБА Т.П.
ИССЛЕДОВАНИЕ ЭФФЕКТИВНОСТИ РАБОТЫ ШНЕКОВОГО ИСПОЛНИТЕЛЬНОГО ОРГАНА ОЧИСТНОГО КОМБАЙНА

Исследования показали, что увеличение шага расстановки резцов с 45 на 60 мм позволяет улучшить гранулометрический состав отбиваемой руды, увеличение ширины захвата в исследованном диапазоне позволяет повысить производительность комбайна на 25%, а за счет перераспределения объемов добычи из кутковых зон в линейные происходит повышение производительности с одновременным снижением скорости подачи при одинаковой загрузке привода шнекового исполнительного органа комбайна.
Ключевые слова: шнековый исполнительный орган, резцы, шаг расстановки, линии резания, режимы работы, геометрические параметры, ширина захвата, кутковые и линейные зоны.

ZAKHAROV Y.N., SHCHERBA T.P.
STUDY OF THE EFFECTIVENESS OF A CUTTING DRUM OF A SHEARER

The article describes the studies of executive elements of cutter-loaders. The actual parameters of spacing of cutters on executive elements of cutter-loaders to be used in potash mines were determined directly in production headings.
The author analyzed the influence exerted by straight-line cutter spacing of executive elements of cutter-loaders on grain-size composition of broken ore and by cutting width of cutter-loaders on cutting feed rate. The conclusions are drawn and the recommendations on the cutter spacing are made.
The study shows that an increase of picks location spacing from 45 mm to 60 mm lets improve the ore’s granulometric composition. The increase of web depth in the investigated range lets improve the capacity of a shearer by 25 per cent. An increase in capacity takes place while reducing the feed rate by the same charging of a drive of a cutting drum of a shearer by the reallocation of production volumes from side-draw zones to line zones.


ИГНАТКИНА В.А., БОЧАРОВ В.А., ПУНЦУКОВА Б.Т., АЛЕКСЕЙЧУК Д.А.
ТЕРМОДИНАМИЧЕСКИЕ И КИНЕТИЧЕСКИЕ ПАРАМЕТРЫ АДСОРБЦИИ КОМПОЗИЦИИ СУЛЬФГИДРИЛЬНЫХ СОБИРАТЕЛЕЙ НА СУЛЬФИДНЫХ МИНЕРАЛАХ

Приведены экспериментальные данные изучения адсорбции бутилового ксантогената, изобутилового дитиофосфата, О-изопропил-N-метилтионокарбамата и их композиции на пирите, халькопирите с использованием ИК спектроскопии, УФ-спектроскопии, дифференциально-сканирующей калориметрии. На основании результатов адсорбции, экспериментальной энергии активации, энтальпии десорбции собирателей с поверхности с поверхности пирита установлено, что снижение флотационной активности пирита происходит за счет более низкого сродства дитиофосфата и тионокарбамата к его поверхности (0,63 и 1,0) и более высокого сродства к поверхности халькопирита (0,78 и 2,5), что и проявляется в константах скорости адсорбции (кдтф-Fes2 = 1,00•10-7 М•м-2•с-1; кдтф-CuFes2 = 5,71•10-7 М•м-2•с-1; кТК-Fes2 = 3,45•10-7 М•м-2•с-1; кТК-CuFes2 = 11,10-7 М•м-2•с-1) и в различиях в молекулярной структуре поверхностных соединений.
Ключевые слова: адсорбция, флотация, сульфидные минералы, собиратели, кинетические константы, энергия активации, поверхностные соединения.

IGNATKINA V.A., BOCHAROV V.A., PUNTSUKOVA B.T., ALEKSEYCHUK D.A.
THERMODYNAMIC AND KINETIC PARAMETERS OF ADSORPTION OF SULFHYDRYL COLLECTOR COMPOSITION ON SULFIDE MINERALS

The paper covers experimental data of studying the adsorption of butyl xanthate, isobutyl dithiophosphate, O-isopropyl-N-methyl thionocarbamate and their combinations on pyrite and copper pyrite by different instrumental methods (IR spectroscopy, UV spectroscopy, DSC differential scanning calorimetry). Based on the parameters of adsorption, adsorption constants and experimental activation energy, enthalpy of desorption of collectors from the surface of pyrite collectors, we justified the use of dithiophosphate and thionocarbamate compositions to reduce the flotation of pyrite with a sufficiently high recovery of copper pyrite, which is due to the difference in affinity of dithiophosphate and thionocarbamate to the pyrite (0.63 and 1.0) and copper pyrite (0.78 and 2.5) surface, manifested in kinetics of adsorption (kdtf-FeS2 = 1.00 М•10-7•m-2•s-1; kdtf-CuFeS2 = 5.71 М•10-7•m-2•s-1; kTK-FeS2 = 3.45 М•10-7•m-2•s-1; kTK-CuFeS2 = 11.1 М•10-7•m-2•s-1) and the difference in forms of fixation of sulfhydryl collectors.
Key words: adsorption, flotation, sulfide minerals, collectors, kinetic constants, activation energy, surface compounds.


КАРМАЗИН В.В., СЫСА П.А.
СЕПАРАЦИЯ В ВЫСОКОГРАДИЕНТНЫХ ПЕРЕМЕННЫХ МАГНИТНЫХ ПОЛЯХ С НИЗКОЙ НАПРЯЖЕННОСТЬЮ

Рассмотрена высокоградиентная сепарация в слабых переменных магнитных полях с целью повышения качества магнетитовых концентратов.
Ключевые слова: высокоградиентная сепарация, поле с малой напряженностью, магнетитовый концентрат.

KARMAZIN V.V., SYS P.A.
HIGH-GRADIENT LOW-STRENGTH VARIABLE MAGNETIC SEPARATION

Quality iron ore depletion worsens with rich types and with increasing depth of pits, and therefore the quality of iron ore for the steel industry is constantly decreasing.
Basic equipment concentrators are drum separators, which have a limit on the iron content in the concentrate. The main drawback of these separators — low selectivity, which resulted in the final concentrate fall poor splices, its quality deteriorates. Nonmagnetic concentrates on fine-tuning methods either expensive or ineffective. The proposed method involves the use of high-gradient enrichment separation of strongly magnetic grains to extract pulp. Тне feature of this method is the low intensity of the magnetic field of the magnetic system and use it for AC power. When applying a weak magnetic field and high-gradient spin system is not complete flocculation of the pulp occurs because this lacking of magnetic field and the material remains in a relatively freely suspended. Laboratory examination of the process was conducted in a pilot plant. It consists of a cassette of thin metallic wires placed inside the solenoid connected to an AC source. The study was able to improve the quality of the concentrate. Application of this method allows to obtain concentrates commercial quality suitable for use in the reduction metallurgy without using flotation, which increases environmental safety, significantly reduces costs and improves production efficiency, respectively.
Key words: high-gradient separation, low field strength, magnetite concentrate is.


КИСЛОВ Н.В.
ВЗАИМОСВЯЗЬ МЕЖДУ ПОКАЗАТЕЛЯМИ НЕОДНОРОДНОСТИ ПО РАЗМЕРАМ ЧАСТИЦ ИЗМЕЛЬЧЕННОЙ ГОРНОЙ ПОРОДЫ

Приведены результаты описания характеристик распределения частиц по фракции измельченных материалов, дается математическая оценка этих распределений с помощью параметров, характеризующих условный средний размер частиц их полидисперсных смесей и неоднородность фракционных составов по размерам частиц. Установлена взаимосвязь между показателями неоднородности по размерам частиц измельченных горных пород.
Ключевые слова: горная порода, измельчение, фракции частиц.

KISLOV N.V.
INTERRELATION OF HETEROGENEITY INDICATORS ACCORDING TO THE SIZE OF PARTICLES OF THE CRUSHED ROCK

The results of characteristics of particles distribution according to the crushed material fractions are given. Mathematical estimation of these distributions by means of the parametres characterising the conditional average particle size of their polydisperse mixes and heterogeneity of fractional structures according to the size of particles is considered. Interrelation of heterogeneity indicators according to the sizes of particles of the crushed rocks is established.
Key words: rock, crushing, fractions of particles.


КОЗЛОВ В.А.
ВЛИЯНИЕ СПОСОБОВ ОБОГАЩЕНИЯ УГЛЯ НА ВЫХОД КОНЦЕНТРАТА В ТЕОРЕТИЧЕСКОМ БАЛАНСЕ ПРОДУКТОВ НА ПРИМЕРЕ ДЕНИСОВСКОГО МЕСТОРОЖДЕНИЯ ЮЖНО-ЯКУТСКОГО КАМЕННОУГОЛЬНОГО БАССЕЙНА

Обозначена проблема влияния способов обогащения угля в схеме углеобогатительной фабрики на результат расчета теоретического баланса продуктов на примере исследований угля Денисовского месторождения Южно-Якутского каменноугольного бассейна.
Ключевые слова: фракционный состав, обогатимость угля, баланс продуктов.

KOZLOV V.A.
EFFECT OF THE COAL PREPARATION METHODS ON THE CONCENTRATE YIELD IN THE THEORETICAL COAL-CLEANING BALANCE IN TERMS OF THE DENISOVSKY COALFIELD, SOUTH YAKUTIA

The author points at the presence of influence exerted by coal preparation methods used at a coal-cleaning plant on the theoretical coal-cleaning balance calculation in terms of the analysis of coal from the Denisovsky coalfield in South Yakutia. The calculation of the theoretical coal-cleaning balance should account for dressing processes included in the coal-cleaning plant flowsheet, and size classification of coal should be performed accordingly. The calculation should take into account difference of physical principles of dressing processes, e.g., gravity preparation in jig washer or float-and-sink cyclone and foam flotation of slurry coal. In this case, the theoretical coal-cleaning balance depends both on the float-and-sink analysis data and the slurry coal flotation results, and the calculated concentrate yield is in this case lower than in the common calculation based on the float-and-sink analysis outcome. A real-world yield of concentrate, considering errors of coal classification on the available washing equipment, cannot exceed the theoretical concentrate yield. Thus, we have an appropriate maximum concentrate yield constraint. The knowledge of this fact will allow tender committees to appreciate competitive bids on new coal preparation plant projects.
Key words: fractional composition, coal washability, coal-cleaning balance, concentrate yield, ash content, coal flotation.


КУКЛИНА Г.Л.
ОЦЕНКА ВЛИЯНИЯ МЕХАНОХИМИЧЕСКИХ ПРОЦЕССОВ НА ТЕХНОЛОГИЧЕСКИЕ СВОЙСТВА УГЛЕЙ ВОСТОЧНОГО ЗАБАЙКАЛЬЯ КАК СЫРЬЯ ДЛЯ ПОЛУКОКСОВАНИЯ

Приведены результаты полукоксования орогенных углей Восточного Забайкалья и их интерпретации с учетом генезиса угольных месторождений региона в условиях непрерывного проявления тектонических процессов.
Ключевые слова: угли, Восточное Забайкалье, полукоксование, механохимические процессы.

KUKLINA G.L.
INFLUENCE OF MECHANOCHEMICAL PROCESSES ON PROCESSING BEHAVIOR OF EASTERN TRANSBAIKALIA COAL UNDER LOW-TEMPERATURE CARBONIZATION

The article gives results of semicoking of the orogenic coals of the Eastern Transbaikal and their interpretation with regard to genesis of coal deposits in the region under the conditions of continuous manifestation of tectonic processes.
Key words: coals, Eastern Transbaikal, semicoking, mechano-chemical processes.


ЛИТВИНОВА Н.М., АЛЕКСАНДРОВ А.В., БОГОМЯКОВ Р.В.
НЕКОТОРЫЕ НАПРАВЛЕНИЯ ПОВЫШЕНИЯ ЭФФЕКТИВНОСТИ ПРОЦЕССОВ ГРАВИТАЦИОННО-ФЛОТАЦИОННОГО ИЗВЛЕЧЕНИЯ ТОНКОДИСПЕРСНОГО ЗОЛОТА

Приведены результаты экспериментальных исследований гравитационного и флотационного процессов обогащения с использованием предварительной подготовки минеральной массы к основным технологическим процессам обогащения. Показана возможность интенсификации переработки глинистых и шламистых золотосодержащих материалов.
Ключевые слова: гравитация, предварительная обработка минеральной смеси, флотация, сорбционные носители, модификация поверхности.

LITVINOVA N.M., ALEXANDROV A.V., BOGOMJAKOV R.V.
SOME DIRECTIONS OF INCREASE OF EFFICIENCY OF GRAVITY-FLOTATION EXTRACTION PROCESSES FOR FINE-PARTICLE GOLD

Experimental research data of gravitation and flotation enrichment processes using preliminary preparation of minerals for basic technological enrichment processes are resulted in the article. The possibility of the intensification of fine clay and gold-bearing materials processing is revealed.
From the experimental research, it is concluded that preliminary reactant treatment of gold-bearing clayey placer sand and modification of sorption carrier for flotation contribute to the controlled change of mineral material properties and higher quality of gravitation and flotation concentrates.
Key words: gravitation, preliminary processing of mineral mixture, flotation, sorptive carriers, surface modification.


МИХАЙЛОВ А.В., ЕПИФАНЦЕВ К.В.
ПРИМЕНЕНИЕ ШНЕКОВОГО ЭКСТРУДЕРА В ГРАНУЛЯТОРАХ ДЛЯ МАЛОЙ ЭНЕРГЕТИКИ

Рассмотрены особенности оборудования для процессов формования торфа. Проведён анализ технологии формования и работы шнекового экструдера.
Изучены образцы грануляторов различных производителей, выявлены особенности системы регулирования и контроля работы.
Ключевые слова: формование торфа, экструзия, шнек, грануляция, фильера, снижение энергозатрат, сушка, кусковое коммунально-бытовое топливо, контроль процесса.

MIKHAILOV A.V., EPIFANTSEV K.V.
SCREW EXTRUDER IN PELLETING MACHINES FOR SMALL-SCALE ENERGY PRODUCTION

In article briefly consider characteristics machinery for formating of peat in extrusion method. Research technology work of screw extrusion. Examine types granulations different producers, compare their characteristics, expose peculiarity system of regulation and control of their work.
Until now wet peat pelleting and subsequent artificial drying of molded peat fuel has not enjoyed wide application in Russia. The main method of lump peat production is afield milling and drying. However, the expending interest in plant molding of multipurpose peat composites calls for choosing pelleting machines of the domestic manufacture.
The author analyzes extrusion treatment of material without heavy thermal-moisture-mechanical impact that causes various intensity changes in the material. The types of extrusion treatment are reviewed together with characteristics of executive elements of extruders, screw rotation speeds, designs and physical characteristics. Under consideration are three types of pelleting machines for similar texture materials, operating in food, chemical and construction industry.
Specifications of different type pelleting machines are compared.
The authors have developed recommendations on an integrated pelleting machine (symbiose of different elements and mechanisms borrowed from food, chemical and construction industry pelleting machines) to be used at the production conversion phase (e.g., conversion of brick manufacture to peat production).
Effective application of the proposed pelleting machine will help to handle problems of small-scale energy production projects, e.g., a pilot project of the domestic lumped-peat fuel prefabrication.
Key words: formation of peat, extrusion, screw, granulation, draw plate, lowering power inputs, druing, lump peat domestic fuel, control of process.


ОПАЛЕВ А.С., БИРЮКОВ В.В., БУРЕНИНА И.В.
ПРИМЕНЕНИЕ СИСТЕМ ИНЖЕНЕРНОГО АНАЛИЗА ДЛЯ РАЗРАБОТКИ МОДЕЛИ ПРОЦЕССА МАГНИТНОГРАВИТАЦИОННОЙ СЕПАРАЦИИ

Рассмотрена возможность использования компьютерного моделирования процесса магнитно-гравитационной сепарации. Предложен метод учета магнитных взаимодействий между ферромагнитными частицами в магнитно-стабилизированном ожиженном слое (MSFB). Представлены графические результаты моделирования.
Ключевые слова: компьютерное моделирование, CFD-метод, магнитное межчастичное взаимодействие, магнитно-гравитационная сепарация, многофазное течение, разделительный объем.

OPALEV A.S., BIRYUKOV V.V.
APPLICATION OF THE ENGINEERING ANALYSIS SYSTEMS FOR DEVELOPMENT OF SIMULATION PROCESS OF MAGNETIC-GRAVITY SEPARATION

The developed analytical model allows studying ferromagnetic suspension flow in a magnetic gravity separator at a first approximation. The modeling plots show that the liquefied ferromagnetic layer, which is a separation medium, with high concentration by volume is present at the separator bottom. The described model can be used to make predictive estimates of separation of multiphase media in the magnetic gravity separators of various design, and for upgrading such separators.
Key words: computer simulation, CFD-method, magnetic interpartical interaction, magnetic-gravity separation, the multiphase fluid, dividing volume.


РЕЗНИК Ю.Н., ШУМИЛОВА Л.В.
ЭКСПЕРИМЕНТАЛЬНОЕ ИЗУЧЕНИЕ ВЛИЯНИЯ ФОТОЭЛЕКТРОХИМИЧЕСКИХ ВОЗДЕЙСТВИЙ НА ПРОЦЕСС ГЛУБОКОГО ОКИСЛЕНИЯ СУЛЬФИДНЫХ МИНЕРАЛОВ

Дан анализ проблем извлечения золота наноразмерного уровня из труднообогатимых руд. Разработан комбинированный метод окисления (физико-химический и бактериальный) на основе направленных фотоэлектрохимических воздействий для выщелачивания золота из упорного сы-рья. На основе полного вскрытия минеральной матрицы в зависимости от вещественного состава и форм нахождения золота достигнуто повышение извлечения металла более чем на 18,4%.
Ключевые слова: дисперсное золото, физико-химические методы активации, формы дисперсного золота, глинистые минералы и углистое вещество.

REZNIK Y.N., SHUMILOVA L.V.
EXPERIMENTAL STUDY OF PHOTOELECTROCHEMICAL EFFECTS ON THE PROCESS OF DEEP OXIDATION OF SULFIDE MINERALS

The author of the article analyses the problems of nanosized gold recovery from complex ore. There has been developed a combined method of oxidation (physicochemical and bacterial) based on forward photoelectrochemical effects to leach gold from refractory raw stock. Complete stripping of mineral matrix depending on gold speciation and occurrence form has guaranteed an increase in the metal recovery of more than 18,4%.
Key words: invisible gold, chemical acseleration, invisible gold forms, clay minerals and carbon substances.


СЫСА П.А., КАРМАЗИН В.В.
ПОВЫШЕНИЕ КАЧЕСТВА МАГНЕТИТОВЫХ КОНЦЕНТРАТОВ ЗА СЧЕТ ВЫСОКОГРАДИЕНТНОЙ СЕПАРАЦИИ В ПЕРЕМЕННЫХ МАГНИТНЫХ ПОЛЯХ С НИЗКОЙ НАПРЯЖЕННОСТЬЮ

Рассмотрен новый метод обогащения магнетитовых кварцитов — высокоградиентной сепарации в слабом магнитном поле.
Ключевые слова: магнетитовые концентраты, высокоградиентная сепарация, бездоменная металлургия.

SYS P.A., KARMAZIN V.V.
IMPROVEMENT IN THE QUALITY OF MAGNETIC CONCENTRATES IN THE HIGH-GRADIENT LOW-STRENGTH VARIABLE MAGNETIC SEPARATION

Magnetic force is the main force in extracting separation magnetism materials that provide large magnetic separation techno-economic advantages. This is the main advantage of magnetic methods and turns their main disadvantage — low selectivity of separation of minerals due to the phenomenon of magnetic flocculation. Basic equipment concentrators are drum separators, which have a limit on the iron content in the concentrate. In the final concentrate fall poor splices, its quality deteriorates.
Nonmagnetic concentrates on fine-tuning methods either expensive or ineffective. The main costs are based on energy and are aimed at the destruction of intermolecular bonds in ores for mechanical separation of particles of beneficial minerals from gangue minerals When applying a weak magnetic field and high-gradient spin system is not complete flocculation of the pulp occurs because this lacking of magnetic field and the material remains in a relatively freely suspended. Laboratory examination of the process was conducted in a pilot plant. It consists of a cassette of thin metallic wires placed inside the solenoid connected to an AC source. The study was able to improve the quality of the concentrate. This method allows to obtain concentrates commercial quality without using flotation, which increases environmental safety, significantly reducing costs and more economically profitable
Key words: magnetite concentrates, high-gradient separation, reduction metallurgy.


ТУРКИН В.Я., ТЯГУШЕВ С.Ю., ШОНИН О.Б.
ПОВЫШЕНИЕ ТЕХНОЛОГИЧЕСКИХ ПОКАЗАТЕЛЕЙ ВИБРАЦИОННОЙ ЩЕКОВОЙ ДРОБИЛКИ СРЕДСТВАМИ АВТОМАТИЗИРОВАННОГО ЭЛЕКТРОПРИВОДА

Приведены результаты экспериментальных исследований вибрационных щековых дробилок ОАО «НПК «Механобр-Техника». Показано, что начальная расфазировка колебаний щек, обусловленная неидентичностью параметров подсистем ВЩД, вызывает существенное снижение производительности и рост энергоемкости. Для улучшения технологических показателей предложена система автоматического управления приводом по критерию максимальной производительности. Приведены результаты испытаний прототипа системы.
Ключевые слова: двухдвигательный привод, вибрационная щековая дробилка, автоматическое управление, производительность, энергоемкость.

TURKIN V.YA., TYAGUSHEV S.YU., SHONIN O.B.
IMPROVEMENT OF TECHNOLOGICAL PARAMETERS OF THE VIBRATION JAW CRUSHER BY MEANS OF FULLY AUTOMATIC ELECTRIC DRIVE

The article reports experimental tests of vibration jaw crushers of Mekhanobr Tekhnika Co. manufacture. It is shown that initial misphasing of jaws due to unequal parameters of the vibration jaw crusher subsystems appreciably degrades productivity and increases energy consumption of the machine.
The automated control algorithm was developed based on computer model of a vibration jaw crusher with twin-engine electric drive. Mathematical base of the model was the interrelated systems of differential equations of the vibration jaw crusher [6] and asynchronous motor.
The test showed that the automated control of the two-engine electric drive of the crusher allowed the 87% increase in the crusher output with the end product grain distribution in accord with the reference variant figures.
It is suggested to improve technological parameters of the crusher by using the automated control by the maximum output criterion. The automated control prototype trials are described.
Key words: two-engine drive, vibration jaw crusher, automated control, output, energy intensity.


ЩЕЛКОВ П.Ю.
ИМИТАЦИОННАЯ МОДЕЛЬ СЕТЕВОЙ СИСТЕМЫ УПРАВЛЕНИЯ ЭЛЕКТРООБОРУДОВАНИЕМ МОЩНОГО ШАГАЮЩЕГО ЭКСКАВАТОРА-ДРАГЛАЙНА

Рассмотрена имитационная модель сетевой системы управления электрооборудованием мощного шагающего драглайна, позволяющая проверить разработанные алгоритмы управления и технические решения по применению сетевых технологий при решении задачи автоматизации управления электрооборудованием мощного шагающего экскаватора-драглайна.
Ключевые слова: сетевая система управления, силовое электрооборудование, мощный шагающий экскаватор-драглайн, сетевые технологии, имитационная модель.

SHCHELKOV P.J.
IMITATING MODEL OF THE NETWORK CONTROL SYSTEM OF THE ELECTRIC EQUIPMENT OF THE POWERFUL WALKING DREDGE-DRAGLAJNA

In article the imitating model of a network control system by an electric equipment powerful walking dragline is considered, allowing to check up the developed algorithms of management and technical decisions on application of network technologies at the decision of a problem of automation of management of an electric equipment of a powerful walking dredge-dragline.
From the analysis of the electrical equipment group installed on shoveling machine model ESH 20.90, it has been found that it is possible to improve the control of the heavy-duty walking dragline by creation of an electrical equipment control network to be scalable, completable, with an open architecture.
The imitation model of the heavy-duty dragline electrical equipment control network has been constructed for validation of control algorithms and other engineering designs involved in the control network creation.
The article presents structural flowchart of the electronic equipment control network imitation model in the LabView environment.
Key words: the Network control system, a power electric equipment, a powerful walking dredge-dragline, network technologies, imitating model.



СКВАЖИННЫЕ ТЕХНОЛОГИИ
Boring technologies


ПЕРФИЛЬЕВА М.А., ХРУЛЕВ А.С.
РАСЧЕТ ЭРЛИФТА ПРИ СКВАЖИННОЙ ГИДРОДОБЫЧЕ ПОЛЕЗНЫХ ИСКОПАЕМЫХ

Проведен сравнительный анализ параметров эрлифтного подъема полученных экспериментальным путем, расчетами по формуле Гейера, по балансу энергий и полученной эмпирической зависимости
Ключевые слова: скважинная гидродобыча полезных ископаемых, эрлифтный подъем.

PERFILEVA M.A., KHRULEV A.S.
AIRLIFT CALCULATION FOR HYDRAULIC BOREHOLE MINERAL MINING

The authors analyze and compare airlift parameters that have been obtained experimentally, calculated using Geier’s formula for energy balance, and derived from an empirical relation.
The airlift characteristics and parameters compared in the articles have been obtained from ample experimental testing both in the laboratory conditions and in afield hydraulic borehole mining of phosphate, motor and gold sands. The calculation of airlift parameters by balance energy inside and outside the airlift allows considering the airlift tool design features and the airlift conditions. The derived empirical relation for the airlift with a short suction nose-piece simplifies the airlift calculation and yields the results that are close to the experimental airlift parameters and the airlift calculations by energy balance.
Key words: hydraulic borehole mineral mining, airlift.



ИЗМЕРЕНИЯ, КОНТРОЛЬ, ДИАГНОСТИКА
Measurement, control, diagnostics


АТРОЩЕНКО Ф.Г., ЛОПАТИН К.А., АСТАПОВА В.А., ПЕТРЯКОВ А.М.
СОЗДАНИЕ БЕЗЛЮДНОЙ РЕЖИМНОЙ СЕТИ НАБЛЮДАТЕЛЬНЫХ ПУНКТОВ НА МЕСТОРОЖДЕНИИ ИМ. В. ГРИБА

Рассмотрены основные гидрогеологические и физико-географические условия месторождения алмазов им. В. Гриба. Освещены проектные решения по созданию режимной сети в процессе разработки месторождения, связанные с необходимостью ведения режимных наблюдений на более чем 120 наблюдательных точках, расположенных в радиусе от 1 до 7 км от центра карьера. При разработке проекта выявлена необходимость создания на месторождении безлюдной системы съема и передачи информации с каждого наблюдательного пункта. Исходя из опыта работы с подобными системами предлагается использовать для режимных наблюдений за природными водами комплекс метрологического оборудования и программного обеспечения.
Ключевые слова: Архангельская алмазоносная провинция, гидрогеологические условия, водопонижающие скважины, наблюдательная сеть, дистанционный автоматизированный контроль.

ATROSHCHENKO F.G., LOPATIN K.A., ASTAPOVA V.A., PETRYAKOV A.M.
DEPLOYMENT OF UNATTENDED OPERATION MONITORING NETWORK AT THE GRIB MINE

The author describes geological, physical and hydrogeological conditions at the Grib diamond open pit mine and presents design approaches to deployment of an operation monitoring network composed of over 120 observation points arranged within a radius of 1 to 7 km relative to the open pit center. The project engineering has highlighted the need of the unattended information retrieval and transition to cover all observation points. On the basis of the experience gained in operation of networks of the same kind, the outfit of metrological equipment and programming support is recommended for the operation monitoring of natural waters.
Key words: Arkhangelsk diamond province, hydrogeological conditions, dewatering wells, monitoring network, automated remote control.


МЕЛЬНИК В.В.
ИССЛЕДОВАНИЕ ПРИЧИН ДЕФОРМИРОВАНИЯ ИНЖЕНЕРНЫХ СООРУЖЕНИЙ

Рассмотрены примеры исследования причин деформирования инженерных сооружений, даны рекомендации по использованию методов диагностики массива горных пород для своевременного прогноза и снижения риска катастроф при недропользовании. Сделаны выводы о возможности использования разработанных методик для обеспечения безопасного строительства и эксплуатации объектов недропользования.
Ключевые слова: деформирование инженерных сооружений, массив горных пород, геодинамическая активность, метод спектрального сейсмопрофилирования.

MELNIK V.V.
ANALYSIS OF ENGINEERING CONSTRUCTION DEFORMATION CAUSES

In article examples research the reasons of deformation engineering constructions are considered, recommendations about use methods diagnostics of rock massif for the timely forecast and decrease in risk of accidents are subsurface use. The possible use of the developed techniques for safe building and operation of objects are drawn.
Key words: deformation engineering constructions, rock massif, geodynamic activity.



ГОРНЫЕ МАШИНЫ, ОБОРУДОВАНИЕ И ТРАНСПОРТ
Mining machinery, equipment and transport


ВЫСКРЕБЕНЕЦ А.С., ЦАРАХОВ М.Ю., ПЕТРОВ В.К.
ПАРАМЕТРЫ РАБОТЫ ЦЕНТРОБЕЖНОЙ МЕЛЬНИЦЫ

Разработана конструкция ротационной дробилки с целью получения продуктов тонкого помола и зерновых фракций, приведены формулы для расчета основных параметров дробилки.
Ключевые слова: измельчение, ротационная дробилка, зерновые фракции.

VYSKREBENETS A.S., CARAHOV M.YU., PENROV V.K.
CENTRIFUGAL MILL PARAMETERS

The article describes the rotary crusher designed for fine and grain-size milling, and presents formulas for the main characteristics of the crusher.
The circuit scheme and operation of the crusher are described. One of the basic characteristics of the crusher performance is its capacity.
The advantage of the proposed machine is the high-speed destructive effect due to combination of crushing and impact shock.
It is found that the rotary crusher consumes 1.5–1.7 times lower energy as against hammer crushers, processes materials of different moisture content (from 3 to 9%) and produces grains in a wide range of size, depending on the clearance in crushing zone III.
Key words: grinding, rotary crusher, grain size fractions.


ИЛЬЮШИН Ю.В., ТРУШНИКОВ В.Е.
РАЗРАБОТКА ИМПУЛЬСНОГО УПРАВЛЕНИЯ ТЕМПЕРАТУРНЫМ ПОЛЕМ БУРОВЫХ ШНЕКОВ ДОБЫЧИ ГОРЯЧЕЙ МИНЕРАЛЬНОЙ ВОДЫ КИСЛОВОДСКОГО МЕСТОРОЖДЕНИЯ НАРЗАНА

Кисловодское месторождения минеральной воды (нарзана) имеет ряд особенностей, делающих невозможно

Our partners

  • Скопус
  • Почта России
  • Лань
  • Elibrary
  • CyberLeninka
  • crossref
  • ВАК
  • Антиплагиат